Effect of Changing Point Angle and Helix Angle Values of Drill Bit on Bone Drilling Simulation
DOI:
https://doi.org/10.47355/jaset.v4i2.69Keywords:
Orthopedic surgery, bone fracture, drilling temperature, drill bit design, necrosisAbstract
Abstract: Orthopedic surgery treats disorders of the bones and soft tissues, especially in cases of accidental fractures. One method of fracture healing is to place plates and bolts in the bone. However, the drilling process for plate installation can cause an increase in temperature around the drilling area, which risks causing necrosis in the bone. This study aims to examine the effect of drill bit design on the temperature generated during bone drilling. Modifications to the point angle, helix angle of the drill bit can reduce the temperature during drilling. The results of this study suggest that optimizing the drill bit design can reduce the risk of necrosis and improve drilling efficiency, which can accelerate the healing process of broken bones.
Keywords: Orthopedic surgery, bone fracture, drilling temperature, drill bit design, necrosis.
References
W. Hasim and A. Suhadi, “Modifikasi Bentuk Mata Bor Untuk Efisiensi Proses Pembuatan Lubang Baut,” Teknobiz J. Ilm. Progr. Stud. Magister Tek. Mesin, vol. 11, no. 1, pp. 55–61, 2021.
M. Tolouei-rad and M. Aamir, “Analysis of the Performance of Drilling Operations for Improving Productivity,” no. March, 2021.
R. S. Anang Ansyori, “Pengaruh Diameter Mata Bor Terhadap Tingkat Kehalusan Lubang Mata Bor,” vol. 7, no. 1, pp. 7–18, 2019.
A. R. Nasution, F. S. Wahyudi, C. A. Siregar, A. Affandi, and Z. Fuadi, “Pengaruh sudut twist drill terdahap kekasaran dan kebulatan pada proses pemesinan drilling,” SINTEK J. J. Ilm. Tek. Mesin, vol. 17, no. 1, p. 1, 2023.
G. A. Ibrahim, Y. Burhanuddin, and D. Embrijakto, “Analisis Kepresisisan Lobang Bor Pada Pemesinan Magnesium Az31 Menggunakan Metode Taguchi,” FLYWHEEL J. Tek. Mesin Untirta, vol. V, no. 1, p. 29, 2019.
P. W. Ndaruhadi and B. Santosa, “Akurasi Lubang Bor Hasil Proses Pengeboran Pada Material SKD-11,” Pros. SNIJA, pp. 191–195, 2015.
W. Caesarendra, “Bone Drilling: Review with Lab Case Study of Bone Layer Classification Using Vibration Signal and Deep Learning Methods,” Eng, vol. 5, no. 3, pp. 1566–1593, 2024.
R. Mathussa, “Perangkat Pengukuran Eksperimental Suhu Pengeboran Tulang Menggunakan Arduino Uno,” Univ. Lampung, vol. 1, no. 1, pp. 1–50, 2021.
S. Harun and Y. Burhanuddin, “Analisis Termal Proses Pengeboran Tulang dengan Metode Statistik Full Factorial untuk Pengontrolan Nekrosis Tulang,” vol. 19, no. 14, pp. 87–95, 2024.
O. Pazarci, Y. Torun, A. Ozturk, and Z. Oztemur, “Comparative study of different drills for bone drilling: A systematic approach,” Malaysian Orthop. J., vol. 14, no. 2, pp. 83–89, 2020.
